FS25 Tramline Pilot V1.0.0.0

FS25 Tramline Pilot V1.0.0.0

Tramline Pilot V1.0.0.0 creates tramlines for every field, marks them on the ground, and makes the worker drive, turn, spray, and spread only along those lines. The system is based on Control Traffic Farming, keeps the same tramlines for use in later years, and works with AutoDrive for refilling.

Features

• Crops are no longer driven over.
• For refilling, the worker follows the tramlines around the field to leave and enter it again.
• It replaces Precision Farming tramlines, and Precision Farming is not required.
• At the headland, the worker turns along the tramline or uses loops where there is enough room.
• The headland can be sprayed first, sprayed last, or skipped.
• Tramlines in the crop can be made as wheel tracks or as one full lane.
• Display the lines for the current field, for every field, or disable them.
• Saved wheelings are available in every savegame that uses the same map.

Install: Move FS25_TramlineSystem.zip into Documents/My Games/FarmingSimulator2025/mods. When loading your savegame, tick Tramline Pilot in the mod list.

Setup

1. Go to the field and press Right Ctrl+M.
2. Make Tramline spacing match your boom width/spreading width.
3. Choose a Direction and set the number of Headland passes.
4. Press Enter so the tramlines are generated.
5. Fill the sprayer, then drive onto the amber headland tramline.
6. Once the green Start here flag appears, press Alt+T.
7. Use Alt+T or Alt+Q to stop.

Setting up a field

• Direction: use the longest edge, vehicle heading, A – B points (Alt+1, Alt+2), an angle, or the stored direction.
• Tramline spacing: set your boom width, from 6-60 m.
• Headland passes: make 0-4 tramlines around the edge of the field.
• Worker turns: turn along the headland tramline, or make loops where they fit.
• Turn radius: use the sprayer’s turning circle, from 4-15 m.
• Wheel track width: enter the distance between the sprayer’s wheel centres, from 1.50-4.00 m. The width of the machine you are sitting in is marked “your vehicle”. 2m is a good start.
• Headland corners: select round, or back into corners for self-propelled and mounted sprayers.
• Spray headland: choose first, last, or skip.
• Work speed / Turn speed: set the speeds used for spraying and turning.
• Refill with AutoDrive: switch it on or off.
• Create tramlines in crop: select no, wheel tracks, or a full lane.
• Show lines: select off, this field, or all fields.
• Precision Farming tramlines: select on, off on tramline fields, or off everywhere.
• Buttons: Enter generates, Space opens Saved wheelings, Clear field deletes the layout, and Esc goes back.

Seeing your tramlines

• Use Alt+4 to show the lines or hide them.
• The main tramlines appear white, while the headland tramlines appear amber.
• Green indicates the next spraying path for the worker; blue indicates driving with the boom off.
• The starting point is marked by a green flag, and the finishing point by a chequered flag.
• Last sprayed here shows the point where an unfinished job stopped.
• Field gate shows the place where AutoDrive takes over for refilling.

Spraying with the AI worker

1. Put the vehicle on a tramline. Use the headland tramline for a new job, or use a main tramline to begin there.
2. Press Alt+T. The worker sprays the field while staying on the tramlines.
3. Press Alt+T or Alt+Q to stop. Alt+Q can also be used outside the vehicle.
4. Press Alt+T again when you want to continue:

• When restarting at the place where it stopped, it continues there.
• At another location, select Drive back there, Carry on from here, or New job.
• With Back into corners selected, the sprayer reverses into sharp headland corners so they are not missed (not trailed sprayers).
• Saving keeps an unfinished job, allowing you to continue on another day.

Refilling with AutoDrive

Set the arrangement once for each field:

1. In AutoDrive, place a marker on the field edge and use it as the field gate.
2. Make that marker the sprayer’s AutoDrive target.
3. Make the refill point the sprayer’s 2nd target.
4. In the menu, change Refill with AutoDrive to On.

When the tank becomes empty:

1. The worker folds the sprayer and follows the tramlines to the gate.
2. AutoDrive drives it to the refill point and returns it.
3. The worker goes back to the place where the tank ran out and continues.

If AutoDrive stops while travelling, start AutoDrive again or press Alt+T on the field.

Saved wheelings

1. Pressing Generate saves every layout.
2. In the next season, open the field menu and press Space (Saved wheelings).
3. Select the required layout and press Generate.

Saved wheelings are usable in every savegame on the same map.

Tramlines in the crop and Precision Farming

• For Create tramlines in crop, choose Wheel tracks (two tracks 2 m apart) or Full lane (3 m), then press Generate. The crop is removed along the tramlines immediately.
• For Precision Farming tramlines, choose Off on tramline fields or Off everywhere, preventing Precision Farming’s seeders from creating their own tramlines.

Keys

• Right Ctrl+M: opens the setup menu
• Alt+T: starts or stops the worker
• Alt+Q: stops the worker
• Alt+4: shows or hides the lines
• Alt+1 / Alt+2: sets points A and B
• Handy console commands: tlNewJob forgets an unfinished job, tlRefill refills now, tlPaint creates the tramlines in the crop, and tlWheelings / tlLoad / tlSave handle saved wheelings.

If something goes wrong

• “Drive onto the headland tramline”: the vehicle is not on a tramline, so drive to the amber marker.
• It won’t back into corners: the setup needs a self-propelled or mounted sprayer, a headland pass, and Back into corners.
• Refill doesn’t start: make sure the AutoDrive target is a marker at the field edge and that the 2nd target is the refill point.
• The unfinished job has gone: generating a different layout drops it.
• No lines: press Alt+4.
• It can’t follow the corners: set Turn radius to the sprayer’s turning circle.
• Gaps in the wheel tracks: press Generate again after setting Create tramlines in crop to Wheel tracks.