





FS25 Tramline Pilot V1.1.0.0
Tramline Pilot plans tramlines across every field, marks them there, and makes the vehicle drive, turn, spray or spread only on those lines. It is based on Control Traffic Farming, saves the same tramlines for use in later years, and works with AutoDrive for refilling.
Precision Farming is not required.
Place FS25_TramlineSystem.zip in Documents/My Games/FarmingSimulator2025/mods. When loading your savegame, activate Tramline Pilot in the mod list.
Features
- Go onto the field and press Right Ctrl+M.
- Choose Tramline spacing to match the boom width or spreading width.
- Select a Direction and the number of Headland passes.
- Press Enter to generate the tramlines.
- Fill the sprayer, then drive onto the amber headland tramline.
- As soon as the green Start here flag appears, press Alt+T.
- Use Alt+T or Alt+Q to stop.
- Direction options are longest edge, vehicle heading, A – B points with Alt+1 and Alt+2, an angle, or as stored.
- For worker turns, choose along the headland tramline, or loops where they fit.
- Headland corners can be round, or the worker can back into corners for self-propelled and mounted sprayers.
- For Spray headland, choose first, last or skip.
- Work speed and Turn speed control spraying and turns.
- AutoDrive refilling may be switched on or off.
- For Create tramlines in crop, choose no, wheel tracks or a full lane.
- Show lines can be off, limited to this field or set to all fields.
- Precision Farming tramlines can be on, off on tramline fields, or off everywhere.
- The buttons work as follows: Enter generates, Space opens Saved wheelings, Clear field deletes the layout, and Esc goes back.
- Press Alt+4 to show or hide the lines.
- Main tramlines are white, while headland tramlines are amber.
- The green line indicates where the worker sprays next. A blue line indicates driving with the boom off.
- The course start is marked by a green flag, and its finish by a chequered flag.
- Last sprayed here shows the point where an unfinished job stopped.
- Field gate shows where AutoDrive takes over for refilling.
- Drive onto a tramline. Use the headland tramline for a new job, or use a main tramline to begin there.
- Press Alt+T, and the worker sprays the field without leaving the tramlines.
- Press Alt+T or Alt+Q to stop. Alt+Q can also be used outside the vehicle.
- To continue, press Alt+T again. At the place where the worker stopped, it continues there. At another location, choose Drive back there, Carry on from here or New job.
- With Back into corners selected, the sprayer reverses into sharp headland corners so they are not missed. Trailed sprayers are not covered by this.
- Saving keeps an unfinished job, allowing you to continue another day.
- Each layout is saved when you press Generate.
- In the next season, open the field menu and press Space for Saved wheelings.
- Select the required layout and press Generate.
- Saved wheelings are available in every savegame on the same map.
- For Create tramlines in crop, select Wheel tracks, which creates two tracks 2 m apart, or Full lane, 3 m, and then press Generate. The crop is removed along the tramlines immediately.
- Choose Off on tramline fields or Off everywhere for Precision Farming tramlines, preventing Precision Farming’s seeders from making their own tramlines.
Specifications
- Tramline spacing: 6-60 m.
- Headland passes: 0-4 tramlines around the edge of the field.
- Turn radius: 4-15 m.
- Wheel track width: 1.50-4.00 m, measured between the sprayer’s wheel centres. The width of the machine you are sitting in is labelled “your vehicle”. 2m is a good start.
- Wheel tracks: two tracks 2 m apart.
- Full lane: 3 m.
Refilling with AutoDrive
Set this up once for each field:
- In AutoDrive, place a marker on the field edge. This is the field gate.
- Make that marker the sprayer’s AutoDrive target.
- Use the refill point as the sprayer’s 2nd target.
- Set Refill with AutoDrive to On in the menu.
When the tank is empty:
- The worker folds the sprayer and follows the tramlines to the gate.
- AutoDrive takes the vehicle to the refill point and returns it.
- The worker drives back to the place where it ran empty and continues.
If AutoDrive stops on the way, start AutoDrive again or press Alt+T on the field.
Keys
- Right Ctrl+M: setup menu
- Alt+T: start or stop the worker
- Alt+Q: stop the worker
- Alt+4: show or hide the lines
- Alt+1 / Alt+2: set points A and B
- Handy console commands:
tlNewJobforgets an unfinished job,tlRefillrefills now,tlPaintcreates the tramlines in the crop, andtlWheelings/tlLoad/tlSavehandle saved wheelings.
If something goes wrong
- “Drive onto the headland tramline”: you are not on a tramline, so drive to the amber marker.
- It will not back into corners: a self-propelled or mounted sprayer, a headland pass and Back into corners are required.
- Refill does not start: make sure the AutoDrive target is a marker at the field edge and the 2nd target is the refill point.
- The unfinished job has gone: generating a different layout drops it.
- No lines: press Alt+4.
- It cannot follow the corners: set Turn radius to the turning circle of your sprayer.
- Gaps in the wheel tracks: press Generate again after setting Create tramlines in crop to Wheel tracks.
ISSUES: https://github.com/FS-MModding/FS25_TramlinePilot
Changelog
- V1.1.0.0
New – Headland direction: the setup menu now has this option, and at least one headland pass is required. Choose As the vehicle faces, Clockwise or Anticlockwise.
When Clockwise or Anticlockwise is selected, the worker always travels around the headland in that direction. It turns from the headland into the tramlines and returns to the headland at the end, using one curve each time instead of two.
The tramlines continue to be completed up and down, with a turn in one direction at one end and the other direction at the opposite end.
With Back into corners, the worker reverses into every corner from the same side, so each corner uses one corner tramline rather than two.
If it is facing the wrong way, the worker does not start. The start marker says “Turn round” and shows which way the field goes.
Saved wheelings remember the direction.
Fixes – Tramlines made in the crop no longer change into another crop. On maps with extra crops, they appeared as the last crop in the list, onion, for example, on the crop map (GitHub issue #1).
Other – The version number is now 1.1.0.0. The Changelog, README and tutorial on GitHub were updated for the headland direction. - V1.0.0.1
https://github.com/FS-MModding/FS25_TramlinePilot
Fixed – Stopping course
Added – user logging






