





FS25 Tramline Pilot V1.0.0.1
Tramline Pilot lays out tramlines for every field, shows them on the ground, and keeps the vehicle driving, turning, spraying or spreading only along those lines. The system is built on Control Traffic Farming. It saves the same tramlines and uses them again each year. This replaces the tramlines from Precision Farming, so Precision Farming is not needed. AutoDrive can be connected for refilling.
Install: place FS25_TramlineSystem.zip in Documents/My Games/FarmingSimulator2025/mods. When loading your savegame, select Tramline Pilot in the mod list.
Features
- Crop is no longer driven over. During a refill, the worker also follows the tramlines back around to leave the field and return to it.
- The system is based on Control Traffic Farming.
- The same tramlines are saved and used year after year.
- AutoDrive is supported for refilling.
Setting up a field
- 1. Go onto the field and press Right Ctrl+M.
- 2. Set Tramline spacing to match the boom width or spreading width.
- 3. Select a Direction and the number of Headland passes.
- 4. Press Enter so the tramlines are generated.
- 5. Fill the sprayer and drive onto the amber headland tramline.
- 6. Once the green Start here flag appears, press Alt+T.
- 7. Press Alt+T or Alt+Q when you want to stop.
- Direction: longest edge, vehicle heading, A – B points (Alt+1, Alt+2), an angle, or as stored.
- Tramline spacing: your boom width (6-60 m).
- Headland passes: 0-4 tramlines round the field edge.
- Worker turns: along the headland tramline, or loops where they fit.
- Turn radius: your sprayer’s turning circle (4-15 m).
- Wheel track width: the distance between your sprayer’s wheel centres (1.50-4.00 m). The width of the machine you are sitting in is marked “your vehicle”. 2m is a good start.
- Headland corners: round, or back into corners (self-propelled and mounted sprayers).
- Spray headland: first, last or skip.
- Work speed / Turn speed: for spraying, and for turns.
- Refill with AutoDrive: on or off.
- Create tramlines in crop: no, wheel tracks or a full lane.
- Show lines: off, this field or all fields.
- Precision Farming tramlines: on, off on tramline fields, or off everywhere.
- Buttons: Enter generates, Space opens Saved wheelings, Clear field deletes the layout, Esc goes back.
Seeing your tramlines
- Use Alt+4 to display or hide the lines.
- The main tramlines appear in white, while the headland tramlines are amber.
- Green indicates the next spraying path for the worker; blue indicates driving with the boom switched off.
- The course start is marked by a green flag, and its finish by a chequered flag.
- Last sprayed here identifies the point where an unfinished job stopped.
- Field gate shows the place where AutoDrive takes over for refilling.
Spraying with the AI worker
- 1. Put the vehicle on a tramline: use the headland tramline for a new job, or a main tramline when starting there.
- 2. Press Alt+T. The worker sprays the field while staying on the tramlines.
- 3. Press Alt+T or Alt+Q to stop. Alt+Q also works while you are outside the vehicle.
- 4. Press Alt+T once more to continue:
- At the place where it stopped, the worker continues there.
- At another location, select Drive back there, Carry on from here or New job.
- With Back into corners enabled, the sprayer reverses into sharp headland corners, so they are not missed (not trailed sprayers).
- Saving keeps an unfinished job, allowing you to continue on another day.
Refilling with AutoDrive
Configure this once for each field:
- 1. In AutoDrive, place a marker at the field edge: this is the field gate.
- 2. Make that marker the sprayer’s AutoDrive target.
- 3. Choose your refill point as the sprayer’s 2nd target.
- 4. Set Refill with AutoDrive to On in the menu.
When the tank becomes empty:
- 1. The worker folds the machine and follows the tramlines to the gate.
- 2. AutoDrive takes the sprayer to refill and returns it.
- 3. The worker goes back to the point where it ran out and continues.
- If AutoDrive stops on the route, start AutoDrive again or press Alt+T on the field.
Saved wheelings
- 1. Pressing Generate saves every layout.
- 2. In the next season, open the menu on the field and press Space (Saved wheelings).
- 3. Select the layout you want and press Generate.
- Saved wheelings are available in every savegame on the same map.
Tramlines in the crop and Precision Farming
- For Create tramlines in crop, select Wheel tracks (two tracks 2 m apart) or Full lane (3 m), then press Generate. The crop is removed along the tramlines immediately.
- For Precision Farming tramlines, select Off on tramline fields or Off everywhere, preventing Precision Farming’s seeders from creating their own tramlines.
Keys
- Right Ctrl+M: setup menu
- Alt+T: start or stop the worker
- Alt+Q: stop the worker
- Alt+4: show or hide the lines
- Alt+1 / Alt+2: set points A and B
- Handy console commands:
tlNewJobforgets an unfinished job,tlRefillrefills now,tlPaintcreates the tramlines in the crop,tlWheelings/tlLoad/tlSavehandle saved wheelings.
If something goes wrong
- “Drive onto the headland tramline”: the vehicle is not on a tramline; drive to the amber marker.
- It will not back into corners: a self-propelled or mounted sprayer, a headland pass and Back into corners are required.
- Refill does not start: make sure the AutoDrive target is a marker at the field edge and the 2nd target is the refill point.
- The unfinished job disappeared: generating a different layout drops it.
- No lines: press Alt+4.
- It cannot follow the corners: set Turn radius to the turning circle of your sprayer.
- Wheel tracks have gaps: press Generate again with Create tramlines in crop set to Wheel tracks.
ISSUES- https://github.com/FS-MModding/FS25_TramlinePilot
Changelog
- V1.0.0.1
https://github.com/FS-MModding/FS25_TramlinePilot Fixed – Stopping course Added – user logging






